Microstructures and properties of nickel-titanium carbide composites fabricated by laser cladding

In this work, Ni/TiC composites were synthesized by the laser cladding technique (LCT). A scanning electron microscope (SEM), X-ray diffractometer (XRD), microhardness meter, electrochemical workstation, and friction and wear tester examined the microstructure, surface morphology, phase structure, microhardness, wear, and corrosion resistances of the Ni/TiC composites. These results indicated the Ni/40TiC composite contained finer equiaxed crystals than the Ni and Ni/20TiC composites. In addition, numerous TiC particles in the Ni/40TiC composite impeded growth of the nickel crystals, which resulted in the fine microstructure of the Ni/40TiC composite. The Ni, Ni/20TiC, and Ni/40TiC composites exhibited face-centered cubic (f c c) lattices. The average microhardness values of the Ni/20TiC and Ni/40TiC composites were approximately 748 HV and 851 HV, respectively. The Ni/40TiC composite had the lowest friction coefficient (0.43) among all three coatings, and only some shallow scratches appeared on the surface of the Ni/40TiC composite. The corrosion potential (E) of Ni/40TiC exceeded the Ni/20TiC composite, and both were larger than the Ni composite, which indicated the Ni/40TiC composite had outstanding corrosion resistance and the Ni composite had poor corrosion resistance. The corrosion current densities (i) of Ni, Ni/20TiC, and Ni/40TiC composites were 5.912, 4.405, and 3.248 μA/cm², respectively.     

A dense and compact laser cladding layer with solid metallurgical bonding significantly improved corrosion resistance of Mg alloy for engineering applications

Although Mg alloy attracts great attention for engineering applications because of high specific strength and low density, low corrosion resistance limits its extensive use. In this study, Mg–Al–Zn–Mn alloy was treated via a laser cladding process to generate a dense and compact laser cladding layer with solid metallurgical bonding on the substrate for improving corrosion resistance, effectively hindering the corrosion pervasion into Mg alloy. The corrosion current density declined from 103 μA/cm² for Mg alloy to 13 μA/cm² for the laser cladding layer in NaCl aqueous solution. Moreover, the laser cladding layer was slightly corroded in comparison with Mg alloy in NaCl aqueous solution. Besides, the microhardness of the cladding layer reached a mean value of 170.5 HV, 3.1 times of Mg alloy (56.8 HV) due to the in situ formation of hardening intermetallic phases. Wear resistance of laser cladding layer was also obviously improved. These results demonstrated that the laser cladding layer obviously enhanced anticorrosion property of Mg alloy for engineering applications.     

稀土在激光熔覆镍基自熔合金中的作用

采用CO2激光器在低碳钢表面进行激光熔覆处理,研究了稀土氧化物在激光熔覆Ni45自熔合金层中的作用.结果表明,加入适量稀土的熔覆合金层组织得到细化,其在还原酸中的耐蚀性和抗高温氧化能力较不加稀土镍基合金熔覆层都有较大提高,更远高于低碳钢.可见,稀土变质的激光熔覆处理对提高低碳钢性能具有重要指导意义.     

激光熔覆Ni基B4C合金涂层的组织与性能研究

利用5kW连续波CO2激光器对16Mn钢基材表面预置的含20 vol%B4CP的Ni基合金复合粉末进行激光熔覆得到Ni基B4C合金涂层(NiB4c),研究了NiB4c涂层的组织形貌与相组成,并用单纯的镍基合金涂层(Ni60)进行了显微硬度及滑动磨损性能的对比试验。结果表明,NiB4C涂层由涂层下部的胞状晶和涂层中上部的树状枝晶及其间的共晶组织所组成,其组成相为γ-Ni,γ-(Ni,Fe)固溶体和(Cr,Fe)7C3,CrB,Ni3B,Fe2B,Fe23(C,B)6等化合物,涂层中存在未熔的B4C颗粒。激光熔覆NiB4c涂层比Ni60涂层具有较高的硬度和耐磨性,并分析了NiB4C涂层的强化机理。     

激光熔覆专用铁基合金粉末的研究进展

指出了目前防止熔覆层开裂所采取的主要措施中存在的问题,阐述了激光熔覆和热喷涂对于所用合金粉末性能要求之异同,评述了激光熔覆专用铁基合金粉末的研制现状,提出了成分与组织设计的新思想。     

激光熔覆Ni基SiC合金涂层组织与性能的研究

利用5kWCO2连续波激光器在16Mn钢基材表面对含20%(体积比)SiC陶瓷粉末的镍基自熔性合金粉末进行激光熔覆得到Ni基SiC合金涂层(NiSiC)。研究了合金涂层的组织形貌及相结构,并用单纯的镍基合金涂层(Ni60)进行了显微硬度及滑动磨损性能的对比试验。结果表明,NiSiC合金涂层由γ枝晶及其间的共晶组织组成,主要组成相为γ-Ni,γ-(Ni,Fe)固溶体和(Cr,Fe)7C3,Cr23C6及(Cr,Si)3Ni3Si等化合物。添加SiC的镍基合金涂层NiSiC比单纯的镍基合金涂层Ni60具有较高的硬度和耐磨性。     

宽带激光熔覆WCP/Ni基合金梯度复合涂层组织与摩擦磨损特性

研究了铸造WC_P/Ni基合金梯度复合涂层组织与摩擦磨损特性。结果表明,梯度复合涂层与基材实现了良好的冶金结合,涂层内有γ-Ni枝晶组织,γ-Ni＋M₂₃C 6共晶组织以及凝固结晶析出的M₆C、M₂₃C₆、M₇C₃等块状或条状组织;随着铸造WC_P体积分数的增加,复合涂层摩擦系数减小,耐磨性增加。19-4试样的耐磨性最高值为4.61,是基材的3倍以上。梯度涂层的磨损机理为磨粒磨损与粘着磨损的复合作用。     

利用SiO2包膜技术提高群青蓝颜料耐酸性的研究

采用廉价的SiO2 对群青颜料进行致密包膜 ,使群青颜料耐酸性能得到提高 ,解决了群青在聚氯乙烯型材使用中产生的变色现象 ,拓宽了应用范围     

La2O3对激光熔覆TiC/Ni基复合涂层的影响

利用CO2横流激光器在低碳钢基体表面熔覆含稀土氧化物La2O3的镍基TiC金属陶瓷复合层,研究了不同含量的La2O3对激光熔覆镍基金属陶瓷复合层组织及性能的影响。结果表明,加入适量的稀土氧化物La2O3可有效改善激光熔覆复合层的显微组织,减少复合层中的裂纹、孔洞、夹杂;加速复合层中TiC颗粒的溶解和改善TiC颗粒的形状变化,同时,熔覆复合层的耐磨性和耐蚀性明显提高。     

YAG激光熔覆的研究现状与发展趋势

本文介绍了YAG激光熔覆的特点，并与CO2激光进行了比较，显示了YAG激光熔覆的优势和潜力。叙述了YAG激光熔覆的研究进展及其应用前景。